Menu overview

- About
- Products
      -> SuperTherm
      -> RustGrip
      -> EnamoGrip
      -> Hot Pipe Coating
      -> Moist Metal Grip
      -> EnduRoof
      -> EnduRoof 2K
      -> more...
- References
- Distributors
- Contact

EnamoGrip® is a tough, moisture curing, two-component polyurethane enamel, which produces a uniquely hard and durable coating film. EnamoGrip® will demonstrate unsurpassed semi-gloss retention, colour-retention, graffiti-resistance, and chalk resistance, when utilized for exterior coating situations, and will provide outstanding resistance to water and humidity, stains, chemicals, and solvents, as well as tremendous scuff-, mar-, and impact-resistance.

 

  • Self-leveling when applied, gives a glossy, smooth-finished surface appearance.

  • Applied as a clear coat, or is tintable to any colour desired.

  • Extremely tough, EnamoGrip® makes an excellent floor coating.

  • Easily applied to steel, aluminum, concrete or wood.

  • Exceptional graffiti-resistance.

  • Submergible - water resistant

  • 20+ year lifespan on roofing under normal conditions.

  • Topcoat over RustGrip® when specific colour is needed, to give a long life to the surface, or to protect against water ponding.

  • Applied over SuperTherm® to give the best possible protection for a substrate, or to protect against water ponding.

  • Protects against UV, wear, weathering, and moisture penetration.

  • Seals against breathing moisture/gases and protect against weathering and acid/solvent contact.

  • Anti-graffiti protection for surfaces. Applied and cured, EnamoGrip® can resist the permanent damage of vandalism.

  • Vehicle and equipment finishes.

  • Flooring, especially when combined with anti-slip elements.

Although SuperTherm® can be applied by non-professionals, SC2 Trading recommends using a certified applicator. To get more information, please contact us at info@sc2trading.com.

 

Preparation

  • Surface must be clean and completely dry, with no loose debris or particles, rust, dirt, oil, films or residues of any kind. EnamoGrip® will cover previous coatings if they are fully adhered to the surface.

  • Mechanically stir base.

  • Mix curing agent into base and let sit for 30 minutes before applying.

 

Application methods

  • Airless or pot sprayed: tip size 0.66mm; apply in two coats.

  • Roller: use ¼” nap commercial roller; apply in two coats.

  • Brush: apply in two coats

  • Add an additional coat for vertical surfaces

 

Applied rate: Metal: 6.13m2/liter
Concrete or wood: 2.45-3.68m2/liter
Film thickness: Wet: Metal - 0.127-0.176mm   Wet: Concrete - 0.30-0.38mm
Dry: Metal - 0.051-0.076mm   Dry: Concrete - 0.127-0.176mm
Temperature: 10°C (50°F) - 38°C (100°F)
Colder temperatures will increase dry time.
Dry times: 1 hour to touch.
4 hours to handle.
2 hours to recoat.
Full cure: 4-5 days in warm temps.
7-10 days in cool temps.
Precautions: 6-8 hour pot life
Strong odour during application and initial curing.
Limitations
  • Not intended for use on food preparation surfaces that are in direct contact with foodstuffs.
  • Do not apply over wet or moist surfaces. Surfaces must be completely dry.

 

 

Brochures

      -> Brochure English

Technical Information

      -> MSDS sheets
          -> English
          -> Nederlands
          -> Deutsch
      -> Tran Document
          -> English
          -> Nederlands
          -> Deutsch
      -> Tech Sheet & Application Data

Tests

      -> Hydrostatic Preasure
      -> Sterling Board
      -> Vapor Transmission
      -> ASTM-E96

References

      -> Swimming Pool
      -> Gold Certificate

EnamoGrip® projects

 
 

Superior Coatings & Concrete Trading

Beverweertseweg 60, 3985 RE, Werkhoven

The Netherlands

KvK nr: 8150219

General Terms - Algemeine konditionen - Algemene Voorwaarden - Contact

z